Water Pressure Sensor
Solar-powered, long-range, and built for New Zealand conditions. Everything you need to monitor your farm water system.
💧 Pūkeko Signals Water Pressure Sensor
Solar-powered water pressure monitoring designed for New Zealand farms. Connects via the One NZ NB-IoT network for reliable long-range communication - even in remote locations. Install it at the tank, the pump, or anywhere along the pipeline - wherever works best for your setup. Alerts you by SMS when pressure drops, so you know about a problem before the trough runs dry. Works equally well on scheme-fed systems - if you're on a council or private water scheme, the sensor monitors pressure at your connection point and alerts you to a burst line or disconnected fitting before it becomes a large water bill.
Pressure Sensor
| Maximum sensor pressure | 150 PSI |
|---|---|
| Accuracy | ±5% |
| Resolution | 1 PSI |
| Sensor material | Sensor: Brass - Fitting: glass fibre reinforced nylon |
| Sensor mounting | 20mm BSPT male thread. Use any size Tee that matches your pipe - a reducing bush adapts the Tee down to the sensor thread. No bush needed for a 20mm Tee. See fittings section |
| Cable length | 1.2 metres |
Connectivity
| Network | One NZ NB-IoT (Narrowband IoT) |
|---|---|
| Coverage | Variable coverage across New Zealand including Chatham Island. Check the coverage map |
| Data transmission | Every 20 minutes to 3 hours (adaptive based on battery level) |
| Pressure sampling frequency | Approximately every minute |
Power
| Power source | Solar panel with 3.7V Li-Ion rechargeable battery |
|---|---|
| Solar panel | Integrated solar panel |
| Battery replacement | Not required under normal conditions. See replacement fees below if required. |
| Charger | USB charging cable included. USB charger not included. |
Physical
| Enclosure rating | All-weather resistant for outdoor use |
|---|---|
| Operating temperature | -10°C to +45°C |
Dashboard & Alerts
| Dashboard access | Web-based at dashboard.pukekosignals.co.nz - Android and iOS apps available |
|---|---|
| Alerts | SMS notifications for pressure threshold breaches |
| Multi-sensor support | Monitor multiple sensors from one account |
Pricing
| Hardware | $290 + GST (one-time) |
|---|---|
| Monthly subscription | $12 + GST per sensor - includes network connectivity, dashboard access & SMS alerts |
Warranty & Repairs
| Warranty | Covered for product faults and manufacturing defects for as long as your subscription is active. This covers the device stopping working due to a fault - not physical damage caused by misuse, accident, or environmental damage beyond normal outdoor use. If the One NZ NB-IoT network is ever shut down, we will replace your device with one that works on the available network at no hardware cost. |
|---|---|
| Unit replacement | Sending unit replacement (without sensor) - $150 + GST Sensor module replacement - $50 + GST |
| Component repairs | Antenna replacement - $40 + GST Sensor cable replacement - $30 + GST Solar panel replacement - $30 + GST Battery replacement - $50 + GST |
💡 What's included
Each sensor comes with:
- Water pressure sensor unit
- USB charging cable
- Product registration code card
- Installation guide
💡 What you need to purchase separately
You will need:
- A Tee (T-join) fitting that matches your pipe size
- A reducing bush to adapt the Tee to the 20mm sensor thread (not required if using a 20mm Tee on a 20mm pipe)
| Pipe size | Anka Tee | Hansen Tee | Hansen Reducing Bush |
|---|---|---|---|
| 20mm / ¾" | AFT20 | HFT20 | N/A |
| 25mm / 1" | AFT25 | HFT25 | HRB2520 |
| 32mm / 1¼" | AFT32 | HFT32 | HRB3220 |
| 40mm / 1½" | AFT40 | HFT40 | HRB4020 |